A10VSO柱塞泵壓力調節問題與壓力升不上來的常見故障解決方案
更新時間:2022-01-13 點擊次數:846次
A10VSO柱塞泵在平時運作的情況下必須定期維護工作壓力是不是不太好,務必立即調節。因此,液壓設備梳理小結了A10VSO柱塞泵平時運作壓力調節方式的說邁,包括平時的壓力調節問題與壓力升不上來的常見故障根本原因與解決方案。
一、A10VSO柱塞泵壓力調節方式
1、液壓泵工作壓力,調節泵的閥門或溢閥流,使A10VSO柱塞泵的工作壓力比較大負荷時的工作壓力大100/< ~ 20%。
2、迅速行程安排的壓力。調節泵的拋撐閥,使其比迅速行程安排需要的具體壓力大15% ~ 20%。
3、從新調節壓力繼電器的彈黃,使其小于液壓泵正常工作壓力0.3 ~ 0. 5MPa (在工作中構件終止或頂在擋鐵上開展)。
4、接換次序。調節限位開關、先導閥、擋鐵、碰塊及自檢測儀,使接換次序以及精準水平考慮工作中構件的規定。
5、工作中構件的速率以及穩定性。調節溢流閥、調節閥、自變量液壓泵或自變量油馬達、進氣系統及密封性設備,使工作中構件健身運動均衡,沒有沖擊性和震動,不允許有外泄露,在有負荷的狀況下,A10VSO柱塞泵速率著陸不可超10%~20%。
二、A10VSO柱塞泵壓力升不上來
1、汽油泵不了油或總流量不夠
2、調速閥調節壓力太低或出現常見故障
3、系統軟件中有泄露
4、因為汽油泵長期工作中震動,使泵蓋螺絲松脫
5、吸進管路漏汽.
6、去油不充足
7、變量柱塞泵壓力調節不善
三、A10VSO柱塞泵壓力升不.上來解決方案
1、同上述情況清除方式
2、再次調節調速閥壓力或修補調速閥
3、查驗系統軟件、修復泄露點
4、適度扭緊螺絲
5、查驗各相接處,并給予密封性、擰緊
6、同上述情況清除方式
7、再次調節A10VSO柱塞泵至所需壓力
感謝你的觀看,以上知識希望幫助您更好的了解。